Execution time #15
Comments
|
Il giorno mar 22 nov 2022 alle ore 14:15 immortal_sniper1 <
***@***.***> ha scritto:
So is is normal for the script to take hours to run on a 4 layer board?
Nope the script is usually quite fast and I don't think there's a way to
make it faster since the placement is made
scanning the area horizontally and vertically and checking the room for the
via...
I did run it with great effect on 2 layer boards and it was fine. but not
it takes ages, i can see that some vias were placed both in layout and 3d
model but kicad is frozen.
Could you share a pcb file where I can reply the same issue?
Also on a side note is there a way to tell the script not to put vias in
certain areas so that i can later remove that zone and stitch with another
net?
This depends on what you mean with area.... if it is a named object that is
accessible through KiCAD python API we can find a way to access it and
check if via falls inside its borders and so on...
Again if you can provide a PCB file with such an element I can check if
this feature can be *implemented*.
|
|
https://github.com/immortal-sniper1/Bird_Detector/tree/master/Bird_detector_V1 I also tried on another board with a net that is not gnd and it did not trigger regarding the area i want to not put vias inside a SMA connector or small areas like that |
|
Il giorno mar 22 nov 2022 alle ore 17:29 immortal_sniper1 <
***@***.***> ha scritto:
I'll make a try on this board and I'll let you know..
I also tried on another board with a net that is not gnd and it did not
trigger
again without a 'problematic' pcb file the reply of issue is uncertain...
regarding the area i want to not put vias inside a SMA connector or small
areas like that
We have to find a way to 'classify' such kind of components. Not too
difficult I'll think about it.
… —
Reply to this email directly, view it on GitHub
<#15 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABOP54RMRJH4HSRECKWEY5LWJTYFHANCNFSM6AAAAAASHZ4RJU>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
bye by(t)e[s]... WeirdGyn!
|
|
again without a 'problematic' pcb file the reply of issue is uncertain..... ill upload that board soon too it is not MIT that is why i have to put some other license on it and it is a bit more complicated but i think ill be able to get it done but realistically i am not sure at what time regarding classification maybe this: if it is a THT and pitch is 2-3 times via spacing dont place via there ( just what i can up on the fly but i think this more or less can work) |
|
any updates? |
|
Still working on it.
Il giorno gio 24 nov 2022 alle ore 20:36 immortal_sniper1 <
***@***.***> ha scritto:
… any updates?
—
Reply to this email directly, view it on GitHub
<#15 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABOP54XKMR2YHWASOTPFEPDWJ67U7ANCNFSM6AAAAAASHZ4RJU>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
bye by(t)e[s]... WeirdGyn!
|
|
tried it again on a few boards and again it went wild with RAM and time https://github.com/immortal-sniper1/cross_band_handy_walkie_talkie/tree/master/HW |
So is is normal for the script to take hours to run on a 4 layer board?
I did run it with great effect on 2 layer boards and it was fine. but not it takes ages, i can see that some vias were placed both in layout and 3d model but kicad is frozen.
Also on a side note is there a way to tell the script not to put vias in certain areas so that i can later remove that zone and stitch with another net?
The text was updated successfully, but these errors were encountered: